Відео

Did you measure sag and make the appropriate pre load adjustments to the rear shock?

do you how to remove the speed limiter

I've been doing lots of looking, and the aluminum "crush seal?" washer (causally mentioned in the official Honda manual) for the gear oil drain bolt is never cited by part number. Mine is screwed up, and needs to be replaced. It was leaking until I flipped it over and put the smooth side toward the bike. Lot's of things pop up for sale when I google for the part (Honda crush seal), different diameters versions. (22mm? / 24mm?). I can't find anything on the web where "crush seal" and "Honda Sh150i" appear together. ...except the Honda manual which doesn't cite a part number. It supposedly needs to be replaced every time or every other time. Yet there's zero reference as to what part to buy exactly. I'm also unable to identify it in the parts list/exploded view of the crankcase. Honda - Replace the crush seal often! Me - OK, no prob. But what part number or specific size is it? Honda - Oh, c'mon man. You should know!

Well done you are the only UA-camr who showed the rotations of the tires

Hi, can you switch the tier to tubless ones ? thank you

Paint protection film is way more durable than you think. I've had it installed on the front end of several vehicles and it absolutely blocks any damage that will happen to your vehicle in normal highway driving. Every blemish you tried to fix in this video would have been prevented by PPF.

The service manual says - Brake tluid replacement sequence; (A) Front right -> (B) Rear left-> (C) Front left -> (D) Rear right. Think it's because of the abs location. Cheers

Heat your tires before trying to install. I get mine hot enough to have a little trouble holding them, poop poop chute, They slide on the first side in one shot. Side two does take a bit of effort but it sure is easier than before I knew to heat them up

Thank you for posting this, I found it helpful to take off the right side adjuster, put everything in place and axle ALMOST into final position, and the simply slide in the adjuster. Takes 5 seconds to slide the wheel in this way. Just make sure to count the revolutions required to remove the adjuster so it’s super easy to put back. Thanks again for this video

Excellent tutorial!!! Thanks!!!

Thanks for the video. Do you know if the rear caliper on the brembo trim the same as the non-brembo trim? thanks

Uhh, ahhh,

Ty sir, I was stuck on this for a long time and this helped

I used the shorter spring first & still had the rattle noise on cold starts. Swapped to the longer spring & NO MORE NOISE!! ... some people have had success with the shorter, but I would recommend the longer to save your time

Thank you. I love all your Honda Fit videos. Looking forward to doing this spring replacement for my fit soon.

My hub cap won't go back on evenly. I don't understand what I did wrong

This helped

Does this short shifter suffer from the rattling like the cravenspeed?

Do you think we can install Civic oem shark fin on Honda fit GK

Can this belt be bought outside of free spirit?

Thanks for taking the time to record this. Just what I needed 🙏

Thanks for posting! i have bought tire levers and have new tires to fit to my Honda Grom 2022 and Honda Monkey 2018 at some point in time! and hope to do it myself? Your informative video helped thanks!

thank you!

Thank you!

What size are those wrenches to take the wheel off the scooter

i love the 241 it holds on wet road great. it works in mud and sand great. But they don't last about 2500 miles and they are wore out both of the 244 last a long time i got 3500 miles out of one and still half life but they dont work to well in mud. not bad in sand. and the irc 244 always felt like my tires was low in air pressure the felt spongey i can saw about the shrinko irc 244 about lasting because i hit something and blew it out. but i think it will last.

WHAT ABOUT THe 8 PLASTIC LITTLE BALLS THAT IN THE KIT FOR WHAT ARE THEY.....?

Dose it only have 4 spark plugs?

Goodness! It is amazing how Honda was able to keep the "classic look" of the Cub and hide a gaggle to modern tech tucked in so tight behind the panels... makes me long for the old school simplicity of my 1960s Cub...

Do you have any idea if this cage will fit to xsr900 2023 ??

Wow. I’m watching this vid because I’m planning to switch to a Miata from motorcycles. My reasonings are that during long road trips I have more of a chance to survive in a roadster and more relaxing seat time. I’m looking to improve an ND suspension starting with a longer travel/stroke. Now, I know what suspension kit to get. Thanks for the vid.

would this have been any easier removing the ront wheel? I have to replace a front fender as well. -- any idea ow to remove chrome headlight bezel? Thanks

thanks man.

How do you take off an E6 error

Where/how did you get a replacement screen?? I have this issue and I would like to attempt to replace it myself if I can get the part. Thanks in advance and thank you so much for this video.

Speed make more videos on your speed twin . Subscribed

Did you find any other solutions? Change pegs?

I just changed coolant in my daughters 2015 Forester. I used Prestone MAX Asian Antifreeze/Coolant Prediluted (blue). I read the “Product Safety Data Sheet” on their webpage & the composition/information on Ingredients is the exact same as the new Subaru Super Coolant (black jug) & a lot cheaper off RockAuto. As stated above, please use a Wix 57055XP. Subaru requires a 27 psi for the by-pass valve & Wix meets that requirement. Thanks for the video & God bless

did you use the same size Phillips to remove the cover screws. how did you remove and re-install the cover clips and what tool did you use. Is it enough for the fan to come on for one cycle & then drain the distilled water. When I filled it with the blue coolant & start the engine do I turn the heater on again & is the radiator cap on or off at this time. Thanks for the info.

i love the 241's but they dont seem to last at long as the 244's do but at the price of the tires i will change them more often and stay with the 241's they work great in sand mud and it cuts the water on roads.

this guy dosent know what he talking about . plus the Miata is slow af .

Nice to see how they arrived. Just picked one up, the machining and layout is exceptional. What a sweet little setup for compactness and hunting.

thanks mine is 2019 year ..should be similar

Will it work with a Miata rf

Will a pioneer TS-WX1010A subwoofer fit in a 2013 Miata sport behind the seat or under?

Will the pioneer TS-WX1010A fit in a 2013 Miata behind the passenger seat or under?

Just taken off the rear wheel. Took off the old drum brakes now the wheel won't fit back on. You know what I am doing wrong? I guess there is something else I need to loosen up or something.

I wish you had better tags on this video so i might have found it before I replaced the VTC with Honda's updated one. This is much easier.

I’m riding with my wife in a tandem duo compass. Of course I put the turbos on mine. Ha

This is f’n terrible